Home > Electronics >

BetaFPV F3 Brushed Flight Controller (Frsky Rx + OSD)



 
Alternative Views:


Our Price: $51.99 CAD

Stock Status:In Stock
Product Code: BETAFPV-F3FC-FRSKY-312954
Qty:

Description
 
BetaFPV F3 Brushed Flight Controller (Frsky Rx + OSD)



V1.1 version is available now and the biggest improvement is the integrated Frsky Rx via SBUS protocol. It has a noticeable improvement when the drone turn around.


FEATURES
  • The world's first compatible BetaFlight OSD, FrSky Rx, BetaFlight firmware, born for acro F3 flight controller for the Micro Whoop or Blade Inductrix quadcopter.
  • Fully programmable through Betaflight, using the onboard USB port, tune all the parameters, PID's, and rates to your perfect settings
  • Designed to work with current Tiny Whoop or Blade Inductrix setups
  • Built in Frsky D8 protocol native receiver (SBUS), compatible with almost ALL Frsky radios(e.g. Taranis X9D/X9D Plus/X7) or Frsky compatible transmitter module
  • The flight controller board comes pre-flashed with Betaflight firmware, and pre-soldered 55mm power cable pigtail with JST-PH 2.0 connector, AKA PowerWhoop connector.



SPECIFICATIONS
  • CPU: STM32F303CCT6
  • Six-Axis: MPU6000
  • ESC: All FETs are rated at 6.3A maximum
  • Size: 26mm x 26mm,fully compatible with the Inductrix quad frame and mounting pattern
  • Firmware version: BETAFLIGHTF3 3.1.7
  • OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
  • Receiver: Frsky D8 potocol (SBUS)
  • Power Cable: 55mm, with JST-PH 2.0 connector, AKA PowerWhoop connector
  • Weight: 3.2g






BetaFlight OSD
Betaflight OSD (on screen display) is integrated in BETAFPV F3 brushed flight controllers that shows important flight data on your FPV feed, such as battery voltage, current draw and much more. You can even use it as a menu to change your quad’s PID, rates, filters and other settings.

How would do an OSD with the AIO cameras?

There is a video in and out on the fc itself, labeled CAM and VTX as show below. There should be a video in and out on the AIO camera, like BETAFPV H02 etc. If not, you would have to modify the camera for sure but it would totally be worth it. There is some examples.

BETAFPV H02 Camera, FX806TC, VM275, FX805, Eachine XT02 etc aio camera vtx are available to use the OSD function.



Status LED
This board has 3 LEDs to indicate the status, including Receiver LED ( Red ), FC Status LED ( Red ) and FC Power LED ( Blue ). FC Status LED and Power LED are on the top of the board and Receiver LED is on the button of the board.

LED

Status

Description

Receiver LED ( Red )

Solid

Connected or in bind mode

Receiver LED ( Red )

Flashing

Not connected

Power LED ( Blue )

Solid

Power on

Status LED ( Red )

Solid

Motor Armed


These are 2 high brightness green LEDs on each side of the board. You could find your drone easily when flying.



Frsky Receiver
Currently the built in Frsky receiver is compatible with Taranis, Taranis Plus, X9E, Horus X12S, XJT Modules with International Firmware. With SBUS connection protocol, it has a noticeable improvement when the drone turn around.

Some pilots would complaint that it is definitely not a long range FC. It looses signal with my transmitter far too often and for what appears to be no reason. This issue is often caused by the location of the antenna. You should keep the antenna away from the FC board to get a stronger signal.


Assemble Guide
The mounting pattern of this board is compatible with all the Tiny Whoop airframes, like the original stock Blade Inductrix frame or the Beta75 75mm frame. For other frames like Eachine E010 or E011, a little bit modify is need.

PACKAGE CONTENTS
  • 1 x F3 OSD brushed flight controller V1.1 ( 55mm PH-JST 2.0 power cable soldered)
  • 4 x M1.2x4mm screws (Fit for stock Inductrix frame)
  • 4 x M1.4x5mm screws (Fit for Beta75 etc 75mm frame)
  • 4 x Anti-vibration ruber dampers
  • 1 x 55mm PH-JST 1.25 power cable pigtail

Share your knowledge of this product. Be the first to write a review »